This utility model discloses a special chain for a PVC glove production line with one-sided two-hand mode. This is achieved by setting the two sides of the inner link plate in the inner link of the chain body as right-angle bent plates, and each connecting and fixing a connecting plate with a transverse connecting shaft at its outer end through the bent plates. Due to the adoption of the connecting plate structure with the connecting shafts fixed on both sides of the bent plates, two ceramic hand molds driven by the hand mold holders are installed on each connecting shaft, and the outer width of the supporting roller is adjusted, which not only ensures the chain support The roller runs smoothly in the C-shaped track, and realizes the setting of one-side two-hand molds on the PVC glove production line. In this way, the area of the original production line can be doubled as the original equipment in the same production cycle. Significantly improve work efficiency. And it has the advantages of novel invention concept, scientific and reasonable design, simple and compact structure, reliable working performance, economical and practical, and broad application prospects.
PVC gloves are gloves made of polyvinyl chloride. They are free of allergens, no powder, low dust generation, low ion content, free of plasticizers, grease, silicone, oil and other ingredients, and have strong chemical Resistant, good flexibility and touch, anti-static, convenient and comfortable to wear, so it is widely used in labor protection and family health protection in sanitary inspection, food, chemical, electronics, pharmaceutical and other industries. The market demand is also quite large. The existing PVC glove production line is a chain that is looped into a circle driven by a power mechanism, and a ceramic hand mold fixed by a hand mold holder is installed on each side of the curved plate on both sides of the chain that makes up the chain. The ceramic hand mold follows The chain is dipped in PVC glue during the transmission process, and then dried to form a glove.
Since only one ceramic hand mold can be installed on each side curved plate of the PVC glove production line, the production efficiency is low and the cost increases. With the economic development of society and the gradual improvement of living standards, people's demand for PVC-secondary gloves is also rising, and it is currently unable to meet the market demand. Therefore, how to improve labor productivity and meet market demand has become an urgent technical problem in the field of PVC glove processing.
[Content of the invention]
The purpose of the utility model is to provide a special chain for a PVC glove production line with one-sided two-hand mode, which can significantly improve the processing efficiency of PVC gloves, meet market demand, and solve the problems existing in the prior art.
The technical scheme of the utility model is as follows: It includes a chain main body composed of inner chain links and outer chain links. In the inner chain links of the chain main body, both sides of the inner chain plate are right-angled bent plates, and are bent through the bends. Each board is connected and fixed by a connecting board with a transverse connecting shaft at its outer end.
The connecting plate is a plane with a rectangular upper surface and a truncated cone shape in the middle. The plane is provided with smoothly transitioned 90° hemmings along the two corresponding sides of the length, and the wider end of the plane coincides with the inner link plate bent part. , And a connecting piece composed of a transverse through hole is provided at the flange of the narrow end.
The beneficial effect of the utility model is that it is based on the original chain main body, and is provided with a connecting plate structure with connecting shafts in which the bent plates on both sides are respectively connected and fixed, and two hand mold bases are installed on each connecting shaft to drive The ceramic hand mold, coupled with the adjustment of the outer width of the roller, not only ensures the smooth running of the chain roller in the C-shaped track, but also realizes the setting of the single-sided two-hand mold on the PVC glove production line. There is no need to increase the floor area, and the production efficiency is increased by more than 90% under the energy of the single-hand mold production line, so that the floor area of the original production line can be used, and the products produced in the same production cycle can be two of the original equipment. Times. The purpose of the invention is reliably achieved. And it has the advantages of novel invention concept, scientific and reasonable design, simple and compact structure, reliable working performance, economical and practical, and broad application prospects.
1. A special chain for a PVC glove production line with one-sided two-hand mode, comprising a chain main body composed of inner chain links and outer chain links, characterized in that: both sides of the inner chain plate in the inner chain link of the chain main body are right-angled bends A connecting plate provided with a transverse connecting shaft at its outer end is respectively connected and fixed via the bent plate.
2. The special chain for a PVC glove production line with one-sided two-hand mode according to claim 1, characterized in that: the connecting plate is a plane composed of a rectangle on both ends of the upper surface and a truncated cone shape in the middle, and the plane corresponds to two along the length The side is provided with a smooth transition 90° hemming, the wider end of which coincides with the inner chain plate bent plate part, and the narrow end hemming is provided with a connecting piece composed of a transverse through hole.
3. The special chain for a PVC glove production line with one-sided two-hand mode according to claim 2, characterized in that: a connecting sleeve is built in the horizontal through hole, the connecting sleeve has a small hole facing downward and upward, and a square nut is fixed at the corresponding position outside the small hole , The connecting shaft passes through the horizontal through hole, and the screw is screwed into the socket through the square nut to fix the connecting shaft.