Manufacturing method of hand mold scrubbing machine for nitrile glove production line

- Sep 18, 2020-

Background technique:


The production of nitrile gloves requires hand moulds to be cleaned every cycle. There is currently no complete set of hand mould brushing equipment. Most factories use brush rollers to install separately, which takes up a large area and has poor cleaning effects. In order to improve the cleaning effect, the cleaning agent is often sprayed on the brush, but the cleaning agent will be splashed on the wrist and hand molds. If the oven is not installed to dry this part of the cleaning agent, this part of the cleaning agent will flow down. Wash off the coagulant on the hand mold, causing the gloves to "leak"; if the oven is installed, the production line will be too long, the investment will increase, and the energy consumption will increase. Often when the factory is operating, it will stop spraying the cleaning agent due to "leakage", which will cause the brushes to wear out rapidly, and the service life will be reduced. Over time, the cleaning brushes will be useless, and it will be arranged to stop production and replace hand models or stop production after a while. Cleaning the hand mold seriously affects the normal production. Therefore, the market needs an integrated scrubbing machine that can keep hand molds clean for a long time.

medical nitrile glove dipping machine

Technical realization elements:


In order to overcome the shortcomings of the existing technical solutions, the present utility model provides a nitrile glove production line hand mold scrubbing machine, a combination of two sets of chassis, and two brush rollers in the same chassis, working in a cycle with a conveyor chain. Achieve quick and efficient cleaning, which can effectively solve the problems raised by the background technology.


The technical solutions adopted by the utility model to solve its technical problems are:


A hand mold scrubbing machine for a nitrile glove production line, comprising a rack with a transmission support in the middle of the top, and a chassis provided on both sides of the transmission support. The outer wall of the chassis is horizontally installed with a support, and the top of the support and A geared motor is installed at the bottom, two brush rollers are installed in the cabinet through bearings, and the bearings of the brush roller are installed on the angle steel through the bearing seat adjusting screw, and the angle steel is fixedly installed inside the cabinet. The bearings of each of the brush rollers are respectively connected to the geared motor through a V-belt;


A conveying chain is provided on the top of the transmission support, the conveying chain is linked with a hand mold through a hand mold base, a positioning block rail plate is provided at the connection between the hand mold and the hand mold base, and the positioning block rail plate is connected with a hand mold. Mold seat track.


Compared with the prior art, the beneficial effects of the utility model are:


The conveying chain set on the top of the transmission bracket of the utility model effectively completes the cyclic action of the hand mold base, and at the same time cooperates with two brush rollers to clean the hand mold quickly and efficiently. At the same time, the hand mold located on the outside of the chassis can be processed by the brush , So that large stains on the surface can be cleaned up. Through the transmission of the transmission chain, the hand mold base between the two cases can be converted in real time. When the upper hand mold is scrubbed, the hand mold depends on the positioning rail of the hand mold base to make the hand mold not Turn again, driven by the conveyor chain, the upper hand mold enters the case as shown in the figure. At this time, adjust the gap and position of the two brush rollers so that the brush roller and the water baffle brush can brush as much as possible to the hand mold. For fingertips, finger joints and palms, the two sets of cabinets symmetrically arranged on the top of the scrubber can clean up four hand molds at the same time, which improves the efficiency of cleaning.

Technical characteristics:


1. A hand mold scrubbing machine for a nitrile glove production line, characterized in that it comprises a frame with a transmission bracket arranged in the middle of the top, and a chassis arranged on both sides of the transmission bracket. The outer wall of the chassis is horizontally installed with a support, so The top and bottom of the support are equipped with a geared motor, two brush rollers are installed in the cabinet through bearings, and the bearings of the brush roller are installed on the angle steel through the bearing seat adjustment screw, and the angle steel is fixed Installed inside the cabinet, the bearings of the two brush rollers are respectively connected to the geared motors through V-belts;


A conveying chain is provided on the top of the transmission support, the conveying chain is linked with a hand mold through a hand mold base, a positioning block rail plate is provided at the connection between the hand mold and the hand mold base, and the positioning block rail plate is connected with a hand mold. Mold seat track.


2. A nitrile glove production line hand mold scrubbing machine according to claim 1, characterized in that: the outer wall of the top of the chassis relative to the transmission bracket is provided with a brush, and the inner wall of the top of the chassis is provided with a water retaining wall. scrubbing brush.


3. The hand mold scrubbing machine for a nitrile glove production line according to claim 1, wherein two hand mold holders are symmetrically arranged at one end of the conveyor chain, and the hand molds of one hand mold holder are located on two Between the brush rollers, the hand mold of the other hand mold seat is located between the outer wall of the chassis and the transmission bracket.


The hand mold scrubbing machine for the production line of nitrile gloves according to claim 1, wherein a water spray pipe is provided on the top of the chassis, and a gusset is provided on the bottom of the chassis.


5. A nitrile glove production line hand mold scrubbing machine according to claim 1, characterized in that: the chassis includes another arrangement form, the brush is arranged on the top of the chassis, and at the same time is provided on the outer wall of the chassis Receive the water bucket, and place the hand mold on the top of the brush through the hand mold holder.

Technical summary

The utility model discloses a hand mold scrubbing machine for a nitrile glove production line, which comprises a rack with a transmission bracket arranged in the middle of the top, and a chassis arranged on both sides of the transmission bracket. The outer wall of the chassis is horizontally installed with a support, and the top of the support There are geared motors at the bottom and the bottom. Two brush rollers are installed in the cabinet through bearings, and the bearings of the brush rollers are installed on the angle steel through the bearing seat adjustment screw, and the angle steel is fixedly installed inside the cabinet. The bearings are respectively connected to the geared motor through the V-belt. The top of the transmission bracket is provided with a conveyor chain. The conveyor chain is connected to the hand mold through the hand mold base. The hand mold and the hand mold base are connected with a positioning block rail plate, and the positioning block rail plate is connected with The hand mold seat rail, the combination of two sets of chassis, and the two brush rollers in the same chassis, work in a cycle with a conveyor chain to achieve fast and efficient cleaning.