Manufacturing method of hand-mode brush washing machine for nitrile gloves production line

- Jul 09, 2020-

Background technique:


The production of nitrile gloves requires that the hand mold be cleaned once per cycle. At present, there is no complete set of hand mold brushing equipment. Most factories use brush rollers to install separately, occupying a large area and poor cleaning effect. In order to improve the cleaning effect, the cleaning agent is often sprayed on the brush, but the cleaning agent will be splashed on the wrist and hand mold of the hand mold. If the oven is not installed to dry this part of the cleaning agent, this part of the cleaning agent will flow down. Washing away the coagulant on the hand mold will cause the gloves to "leak"; if an oven is installed, the production line will be too long, the investment will increase, and the energy consumption will increase. Often when the factory is operating, it will stop spraying the cleaning agent due to "leakage", which will cause the brush to wear sharply and reduce its life. Over time, the cleaning brush will be useless, and it will be scheduled to stop production or replace the hand model or production after a period of time. Cleaning hand molds seriously affects the normal production. Therefore, the market needs an integrated scrubbing machine, which can keep the hand mold clean for a long time.


Technical realization elements:


In order to overcome the shortcomings of the existing technical solutions, the utility model provides a nitrile glove production line hand-mode brush washing machine, the combination of two sets of chassis, and with the two brush rollers in the same chassis, in the circulation of the conveyor chain, Achieve fast and efficient cleaning, and effectively solve the problems raised by the background technology.


The technical solutions adopted by the utility model to solve its technical problems are:


A hand-mode brush washing machine for nitrile gloves production line includes a frame with a transmission bracket in the middle of the top, and a chassis provided on both sides of the transmission bracket. A support is installed laterally on the outer side wall of the chassis, and the top of the support and Gear motors are installed at the bottom, two brush rollers are installed in the chassis through bearings, and the bearings of the brush rollers are installed on the angle steel through the bearing seat adjustment screws, and the angle steel is fixedly installed inside the chassis, two The bearings of the brush rollers are respectively connected to the reduction motor through a V belt;


The top of the transmission bracket is provided with a conveyor chain, the conveyor chain is linked with a hand mold through a hand mold base, a positioning block rail is provided at the connection between the hand mold and the hand mold base, and the positioning block rail is connected with a hand Mold base track.

medical latex glove making machine

Compared with the prior art, the beneficial effects of the present invention are:


The conveying chain provided on the top of the transmission bracket of the utility model effectively completes the circulation action of the hand mold base, and at the same time cooperates with two brush rollers to quickly and efficiently clean the hand mold, and the hand mold located on the outside of the chassis can be processed by the plate brush , So that the larger stains on the surface can be cleaned up. Through the transmission of the transmission chain, the hand mold base between the two cabinets can be converted in real time. When the upper hand mold is brushed, the hand mold rests on the positioning rail of the hand mold base to prevent the hand mold from Rotate again, driven by the conveyor chain, the upper hand mold enters the case in the state shown in the figure. At this time, adjust the gap and position of the two brush rollers so that the brush roller and the water baffle brush are washed as far as possible to the hand mold. For fingertips, finger seams and palm parts, the two sets of symmetrically arranged on the top of the scrubbing machine can complete the simultaneous cleaning of four hand molds, improving the cleaning efficiency.

Technical characteristics:


1. A hand-model brush washing machine for nitrile gloves production line, characterized in that it includes a frame provided with a transmission bracket in the middle of the top, and a chassis provided on both sides of the transmission bracket. Both the top and the bottom of the support are provided with a reduction motor, and two brush rollers are installed in the chassis through bearings, and the bearings of the brush rollers are installed on the angle steel through the bearing seat adjustment screws, and the angle steel is fixed It is installed inside the chassis, and the bearings of the two brush rollers are connected to the reduction motor through a V belt;


The top of the transmission bracket is provided with a conveyor chain, the conveyor chain is linked with a hand mold through a hand mold base, a positioning block rail is provided at the connection between the hand mold and the hand mold base, and the positioning block rail is connected with a hand Mold base track.


2. A hand-mode brush washing machine for nitrile gloves production line according to claim 1, characterized in that: a plate brush is provided on the outer wall of the top of the chassis relative to the transmission bracket, and a water blocking is provided on the inner wall of the top of the chassis scrubbing brush.


3. A hand mold brush washing machine for nitrile gloves production line according to claim 1, characterized in that two hand mold seats are symmetrically arranged at one end of the conveying chain, and the hand molds of one hand mold seat are located at two Between the brush rollers, the hand mold of the other hand mold base is located between the outer wall of the cabinet and the transmission bracket.


4. A hand-mode brush washing machine for nitrile gloves production line according to claim 1, characterized in that: a water spray pipe is provided on the top of the cabinet, and a gusset is provided on the bottom of the rack.


5. A hand mold brush washing machine for nitrile gloves production line according to claim 1, characterized in that: the case includes another setting form, the plate brush is arranged on the top of the case, and at the same time, the outer wall of the case is provided with Connect the water bucket, and place the hand model on the top of the board brush through the hand model base.

Technical summary

The utility model discloses a hand-mode brush washing machine for a production line of nitrile gloves, which comprises a frame provided with a transmission bracket in the middle of the top, and a chassis provided on both sides of the transmission bracket. Both the bottom and the bottom are equipped with a gear motor. Two brush rollers are installed in the chassis through bearings, and the bearings of the brush rollers are installed on the angle steel through the bearing seat adjustment screws, and the angle steel is fixedly installed inside the chassis. The bearings are respectively connected to the reduction motors through a V-belt. The top of the transmission bracket is provided with a conveying chain. The conveying chain is linked to the hand mold through the hand mold seat. The hand mold base rail, the combination of two sets of chassis, and the two brush rollers in the same chassis, work in the circulation of the conveyor chain to achieve fast and efficient cleaning.